Lithium Battery
One-component silicone meets the rework process of the lithium battery frame seal and has good waterproof performance and sealing ability. Silicone provides positioning protection for BMS battery management systems as well as excellent thermal conductivity and electrical insulation.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING CONDITION | APPLICATION |
SL129 | BMS control module | Silicone | One component | Moisture cure | PCB coating |
SW 3339 | BMS control module | Silicone | One component | Moisture cure | PCB coating |
SS8188 | BMS control module | Silicone | Two-component | Moisture cure | Pcb board cooling gap filler |
S9339N | Battery case sealing | Silicone | One component | Moisture cure | Box sealing |
SW8339 | Battery case sealing | Silicone | One component | Moisture cure | Box sealing |
EE7006 | Battery case sealing | Epoxy | Two-component | Heat curing | Box sealing |
PP7216 | Soft package battery potting | Polyurethane | Two-component | Heat curing | Potting |
SS0328 | Soft package battery potting | Silicone | Two-component | Moisture cure | Potting |
EE7006 | Battery Cells bonding | Epoxy | Two-component | Heat curing | Cell bonding |
S7139 | Battery Cells bonding | Silicone | One component | Moisture cure | Cell bonding |
EE5006 | Solder joint protection | Epoxy | Two-component | Heat curing | Potting |
EERF5226 | Solder joint protection | Epoxy | Two-component | Heat curing | Potting |
S002PT | Bottom heat sink for Square package battery | Silicon | One component | Moisture cure | Thermal pad |
Automotive Sensor
The trend toward miniaturization, multi-functionality, integration and intelligence of automotive sensors places higher demands on the new processes and new materials.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
SS0328 | Vacuum booster pressure sensor | Silicone | Two-component | Room temperature curing | Potting |
S6449 | Vacuum booster pressure sensor | Silicone | One component | Room temperature curing | Shell sealing |
S6339 | Vacuum booster pressure sensor | Silicone | One component | Room temperature curing | Shell sealing |
S6339 | DPS differential pressure sensor | Silicone | One component | Room temperature curing | Ceramic substrate potting |
ST6339 | DPS differential pressure sensor | Silicone | One component | Room temperature curing | PA66 sealing and bonding |
EE0226 | Hall effect position sensor | Epoxy | Two-component | Heat curing | Shell potting |
EE2016 | Hall effect position sensor/ Tire pressure sensor | Epoxy | Two-component | Heat curing | Shell potting |
EE2116 | Tire pressure sensor | Epoxy | Two-component | Heat curing | Shell potting |
EE4216 | Strain gauge pressure sensor/ Temperature Sensor | Epoxy | Two-component | Heat curing | Potting |
EE126 | Temperature Sensor | Epoxy | Two-component | Heat curing | Induction head potting |
EE4216 | Speed sensor/ Transmission pressure sensor | Epoxy | Two-component | Heat curing | Potting |
EE2116 | Inductive sensor | Epoxy | Two-component | Heat curing | Inductor coil potting |
Electronic Module
Automotive electronic modules include regulators, ignition modules, circuit board three-proof, ECU control modules, charging posts and DC contactors.
PRODUCT | APPLICATION | CATEGORY | PRODUCT TYPE | CURING | APPLICATION |
SS5068 | Regulator | Silicone | Two-component | Room temperature curing | Pcb chip protection |
S6449 | Regulator | Silicone | One component | Room temperature curing | Heat sink and shell bonding |
S5449 | Regulator | Silicone | One component | Room temperature curing | Ceramic substrate and heat sink bonding |
EE126 | Regulator | Epoxy | Two-component | Heat curing | Ceramic substrate and heat sink bonding |
SS5068 | Ignition module/ ECU control module | Silicone | Two-component | Room temperature curing | Pcb board protection |
SS5218 | Ignition module | Silicone | Two-component | Room temperature curing | Pcb board fill protection |
SL129 | PCB Conformal coating/ ECU control module/ Charging pile | Silicone | One component | Room temperature curing | PCB coating |
PP7216 | ECU control module | Polyurethane | Two-component | Room temperature curing | PCB potting protection |
S9339N | ECU control module | Silicone | One component | Room temperature curing | Shell sealing |
S3009 | ECU control module | Silicone | One component | Room temperature curing | Shell sealing |
SS21-0328 | Charging pile | Silicone | Two-component | Room temperature curing | Inductive potting |
S002TP | Charging pile | Silicone | One component | Room temperature curing | Inductor cooling protection |
EE5226 | DC contactor | Epoxy | Two-component | Room temperature curing | Potting protection |
Automotive Display
LCD and TP lamination, recommended to use two-component silicone gel, optical grade transparence material, which can be combined with the various of LCD display modules.
PRODUCT | APPLICATION | CATEGORY | PRODUCT TYPE | CURING | APPLICATION |
SS2068 | LCD and TP lamination | Silicone | Two-component | Room temperature curing | Frame sealing |
S5009 | LCD and TP lamination | Silicone | One component | Room temperature curing | Frame sealing |
Automotive Air Conditioner
PTC heater bonding in automotive air conditioners, one-component addition curing adhesiveis recommended. Potting of resistors is recommended for two-component polyurethane encapsulants.
PRODUCT | APPLICATION | PRODUCT CATEGORY | PRODUCT TYPE | CURING | APPLICATION |
S5449 | PTC Heater | Silicone | One component | Room temperature curing | Thermal bonding |
SS1237 | Resistor | Silicone | Two-component | Room temperature curing | Cavity filling |
PP8066 | Resistor | Polyurethane | Two-component | Room temperature curing | Potting |
Power module
There are many types of electronic modules, common types of power modules, power modules, current or voltage regulator modules, IGBT modules, field effect modules, rectifier modules, IPM modules, PIM modules, thyristor modules, and frequency conversion modules.
PRODUCT | APPLICATION EXAMPLE | CATEGORY | TYPE | CURING CONDITION | APPLICATION |
S8078 | IGBT/Thyristor/Silicon controlled rectifier | Silicone | One-component | Room temperature curing | Chip potting protection |
S6449 | IGBT/Thyristor/Silicon controlled rectifier | Silicone | One- component | Heat curing | Bonding of heat dissipation plate and housing |
S5449 | IGBT/Thyristor/Silicon controlled rectifier | Silicone | One-component | Heat curing | Bonding of ceramic substrate and heat sink plate |
EERF5226 | Thyristor/Silicon controlled rectifier | Epoxy | Two-component | Heat curing | Terminal potting and fixing |
Power device
High-temperature thermosetting one-component epoxy adhesive meets the requirements for sealing of Transistor holes package. The silicone plays a key role in bonding the growth barrier line and the Chips bonding.
PRODUCT | APPLICATION | CATEGORY | PRODUCT TYPE | CURING | APPLICATION |
E8866 | Transistor | Epoxy | One-component | Room temperature curing | Hole sealing |
E51-8866 | Transistor | Epoxy | One component | Room temperature curing | Hole sealing |
SPM0021 | Tantalum capacitor | Silicone | One-component | Room temperature curing | Primer |
SS2-8778 | Tantalum capacitor | Silicone | Two-component | Room temperature curing | Barrier line |
S6449 | Automotive industry | Silicone | One-component | Room temperature curing | Chip adhesive |
Electromagnetic sensor
The encapsulant will satisfies the requirements of good softness and adhesion in electromagnetic sensors. The excellent bonding property, bright surface and moderate toughness will be customized according to the size of sensors, which is the characteristics of the products and services.
PRODUCT | APPLICATION EXAMPLE | CATEGORY | PRODUCT TYPE | CURING CONDITION | APPLICATION |
EEK22016 | Induction door lock | Epoxy | Two-component | Heat curing | Potting |
SS0328 | Induction door lock/Hall sensor/Current sensor | Silicone | Two-component | Room temperature curing | Potting |
PP6066 | Induction door lock | Polyurethane | Two-component | Room temperature curing | Potting |
PP6857 | Hall sensor/Current sensor | Polyurethane | Two-component | Room temperature curing | Potting |
SS5218 | Hall sensor/Current sensor | Silicone | Two-component | Room temperature curing | Potting |
EE3116 | Temperature Sensor | Epoxy | Two-component | Heat curing | Potting |
S1011 | Temperature Sensor | Silicone | One-component | Room temperature curing | Thermal conductivity |
Pressure Sensor
Potting compound meets excellent adhesion, good waterproof and moisture resistance, excellent electrical insulation and stability in pressure sensors.
PRODUCT | APPLICATION | CATEGORY | PRODUCT TYPE | CURING | APPLICATION |
E03-8866 | Pressure Sensor | Epoxy | One-component | Heat curing | Shell bonding |
SS6068 | Pressure Sensor | Silicone | Two- component | Room temperature curing | Potting |
S0249 | Pressure Sensor | Silicone | One-component | Room temperature curing | Potting |
EE7-YJ2-1126 | Pressure Sensor | Epoxy | Two-component | Room temperature curing | Cover bonding |
S0609 | Pressure Sensor | Silicone | One-component | Room temperature curing | Coating |
SS0328 | Throttle sensor/Tire pressure sensor | Silicone | Two-component | Room temperature curing | Potting |
SB2019 | Tire pressure sensor | Silicone | One-component | Room temperature curing | Sealing |
SS2-7078 | Tire pressure sensor | Silicone | Two-component | Heat curing | Potting |
SS6078 | Load cell | Silicone | Two-component | Room temperature curing | Potting |
S9339 | Load cell | Silicone | One- component | Room temperature curing | Sealing |
S0609 | Load cell | Silicone | One- component | Room temperature curing | PCB coating |
PP8108 | Load cell | Polyurethane | Two- component | Room temperature curing | Chip protection |
EE5-0226 | Pressure Switch | Epoxy | Two-component | Heat curing | Potting |
EE51-8866 | Pressure Switch | Epoxy | One component | Heat curing | Potting |
Distance sensor
The distance sensor includes a parking sensor and a displacement sensor. Liquid level sensor, photoelectric sensor.
We will provide different solutions which is based on different sensor requirements.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
SS0328 | Reversing radar | Silicone | Two-component | Room temperature curing | Potting |
S3339 | Reversing radar | Silicone | One component | Room temperature curing | Sealing |
SS1028 | Reversing radar | Silicone | Two-component | Room temperature curing | Potting |
EE2016 | Displacement sensor | Epoxy | Two-component | Heat curing | Potting |
SS0328 | Displacement sensor | Silicone | Two-component | Room temperature curing | Temperature resistance potting |
EE3116 | Liquid level sensor | Epoxy | Two-component | Heat curing | Potting |
EE0226 | Liquid level sensor | Epoxy | Two-component | Heat curing | Potting |
PP0206 | Photoelectric Sensor | Polyurethane | Two-component | Heat curing or Room temperature curing | Soft potting |
EEE0116 | Photoelectric Sensor | Epoxy | Two-component | Heat curing | Potting |
PP8108 | Photoelectric Sensor | Polyurethane | Two- component | Room temperature curing | Potting |
Control module
In the control module, the adhesive is mainly used in the potting of the control power supply and the controller, beginor high-heat-conductive, flame-retardant potting compound plays a key role.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
S9339N | Power Control | Silicone | One-component | Room temperature curing | Box cover sealing |
S0249 | Power Control | Silicone | One component | Room temperature curing | Box cover sealing |
SS0328 | Power Control/Controller | Silicone | Two-component | Room temperature curing | Flame retardant thermal conductivity potting |
PP7216 | Power Control/Controller | Polyurethane | Two-component | Room temperature curing | Potting |
S7609 | Power Control | Silicone | One-component | Room temperature curing | Conformal coating |
S0609 | Controller | Silicone | One-component | Room temperature curing | Conformal coating |
SL129 | Controller | Silicone | One-component | Room temperature curing | Conformal coating |
Instrumentation
In order to ensure the precision of instrumentation,
we has proposed a total solution for instrumentation applications, such as PCB protection, coil fixing, circuit board potting, and lead sealing.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
SS0328 | Electromagnetic instrument | Silicone | Two-component | Room temperature curing | Wiring sealing |
PP216 | Electromagnetic instrument | Polyurethane | Two-component | Room temperature curing | Wiring cavity filling |
PP0206 | Electromagnetic instrument | Polyurethane | Two-component | Room temperature curing | Coil fixing |
SSN9339 | Electromagnetic instrument | Silicone | Two-component | Room temperature curing | PCB potting |
SS2009 | Electromagnetic instrument | Silicone | Two-component | Room temperature curing | PCB coating |
EE8116 | Smart water meter | Epoxy | Two-component | Heat curing | Threading plugging |
SS6078 | Smart water meter | Silicone | Two-component | Room temperature curing | PCB coating |
SS01-8078 | Smart water meter | Silicone | Two-component | Heat curing | Waterproof protection |
SS3009 | Smart water meter | Silicone | Two-component | Room temperature curing | Lead sealing |
S5909 | Smart water meter | Silicone | One component | Room temperature curing | Lead sealing |
Transformer
Adhesive is an indispensable part of transformer it will keep them safe and reliable.
PRODUCT | APPLICATION | CATEGORY | PRODUCT TYPE | CURING | APPLICATION |
EE2016 | Electronic transformer | Epoxy | Two-component | Heat curing | Potting |
EE2116 | Electronic transformer | Epoxy | Two-component | Heat curing | Flame retardant potting |
EE5006 | Electronic transformer | Epoxy | Two-component | Heat curing | Magnetic steel sheet bonding |
EEYJ2-1126 | Electronic transformer | Epoxy | Two-component | Heat curing | End cap |
Electromagnetic induction module
There are many kinds of electromagnetic induction modules.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
S6339 | Electric welder | Silicone | One component | Room temperature curing | Component fixing |
S3019 | Electric welder | Silicone | One component | Room temperature curing | Component fixing |
EE 5016 | Electric welder | Epoxy | Two-component | Heat curing | Coil thermal sealing |
EE3116 | Electric welder | Epoxy | Two-component | Heat curing | Coil thermal sealing |
SB2019 | Reactor | Silicone | One component | Room temperature curing | End cap |
EE1126 | Reactor | Epoxy | Two-component | Heat curing | End cap |
EE3116 | Reactor | Epoxy | Two-component | Heat curing | Potting |
PP7216 | Reed switch | Polyurethane | Two-component | Room temperature curing | Potting |
EE2016 | Reed switch | Epoxy | Two-component | Heat curing | Potting |
E51-8866 | Relay | Epoxy | One component | Heat curing | Plastic sealing |
EE2116 | Mutual inductor | Epoxy | Two-component | Heat curing | Potting |
EE5226 | Mutual inductor | Epoxy | Two-component | Heat curing | Potting |
EE2016 | Permanent magnet sucker | Epoxy | Two-component | Heat curing | Wear-resistant potting |
SSR0038 | Permanent magnet sucker | Silicone | Two-component | Room temperature curing | Coil potting |
PP7216 | Resistor | Polyurethane | Two-component | Room temperature curing | Sealing filling |
S3019 | Resistor | Silicone | One component | Room temperature curing | Square resistance potting |
S2009 | Resistor | Silicone | One component | Room temperature curing | Tubular sealing |
EE5-0226 | Resistor | Epoxy | Two-component | Heat curing | Air conditioning resistance potting |
Optical Fiber Connector
Mainly used in Pvc wire harness sealing and bonding and ABS junction box encapsulation.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
PP7216 | Optical fiber connector | Polyurethane | Two-component | Room temperature curing | Pvc harness sealing and bonding |
EE5006 | Optical fiber connector | Epoxy | Two-component | Heat curing | ABS junction box bonding |
Power Connector
In low-pressure connectors and high-pressure connector potting, we provide different solutions depending on their characteristic.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
SS0178 | Low Voltage Connector | Silicone | Two-component | Room temperature curing | Filled waterproof junction box potting |
S01-8078 | Low Voltage Connector | Silicone | One component | Room temperature curing | Filled waterproof junction box potting |
SS2028 | Low Voltage Connector | Silicone | Two-component | Room temperature curing | Sealed waterproof junction box |
SS1058 | Low Voltage Connector | Silicone | Two-component | Room temperature curing | Sealed waterproof junction box |
EEKK1066 | High Voltage Connector | Epoxy | Two-component | Heat curing | Junction box potting |
PP7216 | High Voltage Connector | Polyurethane | Two-component | Room temperature curing | Junction box potting |
Aerospace Connector
For the sealing of temperature resistance of aerospace connector welding, it is recommended to use two-component epoxy potting compound.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
PP5026 | Aerospace connector | Polyurethane | Two-component | Room temperature curing | Welding temperature resistant seal |
PP2096 | Aerospace connector | Polyurethane | Two-component | Room temperature curing | Welding temperature resistant seal |
PP0226 | Aerospace connector | Epoxy | Two-component | Heat curing | Welding temperature resistant seal |
Automotive Connector
Airtight seals for wire harnesses in automotive connectors are recommended for silicone gels and two-component polyurethane potting compounds.
PRODUCT | APPLICATION | CATEGORY | PRODUCT TYPE | CURING | APPLICATION |
SS7078 | Automotive connector | Silicone | Two-component | Room temperature curing | Wire harness hermetic sealing |
PP7216 | Automotive connector | Polyurethane | Two-component | Room temperature curing | Wire harness hermetic sealing |
EERF5226 | Automotive connector | Epoxy | Two-component | Heat curing | Leakproof terminal fixing |
Automotive Motor
In automotive motors, the adhesive must meet the requirements of waterproofing, secondary insulation, etc., in order to ensure that the car remains stable in harsh environments and road conditions.
PRODUCT | APPLICATION | CATEGORY | PRODUCT TYPE | CURING | APPLICATION |
EE5226 | Automotive motor | Epoxy | Two-component | Heat curing | Stator potting |
EE126 | Automotive motor | Epoxy | Two- component | Heat curing | Magnetic steel tile bonding |
S0249 | Automotive motor | Silicone | One-component | Room temperature curing | Motor cover sealing |
Wind Energy Motor
Wind resource is the inexhaustible treasure of the country. we has a wide range of applications from the bonding of the blades in the wind field and the insulation protection of the motor.
PRODUCT | APPLICATION | CATEGORY | PRODUCT TYPE | CURING | APPLICATION |
PP7-5925 | Wind energy motor | Polyurethane | Two-component | Room temperature curing | Stator potting |
EE2-7156 | Wind energy motor | Epoxy | Two- component | Heat curing | Rotor potting |
S 0939 | Wind energy motor | Silicone | One-component | Room temperature curing | Motor compartment sealing |
SS 9339N | Wind energy motor | Silicone | Two-component | Room temperature curing | Rotor coating repair |
Industrial Motor
Epoxy Adhesives fixed and bond the rotor to reduce the noise, prevent loss and possible media impact, and extend rotor life.
PRODUCT | APPLICATION | CATEGORY | PRODUCT TYPE | CURING CONDITION | APPLICATION |
EE5226 | Industrial motor | Epoxy | Two-component | Heat curing | Stator potting |
EE3116 | Industrial motor | Epoxy | Two- component | Heat curing | Stator potting |
EE126 | Industrial motor | Epoxy | Two-component | Heat curing | Magnetic steel tile bonding |
Water treatment
Polyurethane potting compound is FDA-approved, resistant to acid and alkali, hydrolysis, low mixing viscosity, low heat release, strong bonding with plastics, metals, etc., with a humidity below 25%, low cost.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
EE1-8016 | Curtain filter membranes | Epoxy | Two-component | Heat curing | Membrane wire fixed |
SSW5318 | Curtain filter membranes | Silicone | Two-component | Room temperature curing | Membrane protection |
EE0226 | Column filter membranes | Epoxy | Two-component | Heat curing | Component base bonding sealing |
EE1-2126 | Column filter membranes | Epoxy | Two-component | Heat curing | Component base bonding sealing |
Air filter
We offers polyurethane potting compound, one-component sealant, high temperature resistant glue and jelly gel. It has good temperature resistance, good flow and strong adhesion. It is widely used in air filter for high temperature sealing and potting function.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
SW8339 | High efficiency air filter | Silicone | One-component | Room temperature curing | Filter membrane and the base bonding and fixed |
SR8339 | High efficiency air filter | Silicone | One component | Room temperature curing | Filter membrane and the base bonding and fixed |
Oil Filter
Two-component epoxy potting compound 0226, resistant to moisture, dirt and other atmospheric components, high strength, excellent adhesion, good anti-contamination, no curing by-products.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
EE0226 | Automotive oil filtration | Epoxy | Two-component | Heat curing | End cap bonding |
Photovoltaic Power Generation
The world needs energy, and the sun can provide us with inexhaustible energy for free. Therefore, in the era of promoting environmentally friendly energy, the photovoltaic industry plays an increasingly important role.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
PP255 | Photovoltaic controller | Polyurethane | Two-component | Room temperature curing | PCB potting |
SS0328 | Photovoltaic controller | Silicone | Two-component | Room temperature curing | PCB potting |
SS3-0328 | Photovoltaic controller | Silicone | Two-component | Room temperature curing | PCB potting |
S7609 | String inverter | Silicone | One component | Room temperature curing | Control board coating |
S6339 | String inverter | Silicone | One component | Room temperature curing | Component fixing |
SS0328 | String inverter | Silicone | Two-component | Room temperature curing | Inductive potting |
SS3-0328 | Optimizer | Silicone | Two-component | Room temperature curing | Potting |
SS0328 | Optimizer | Silicone | Two-component | Room temperature curing | Potting |
SB6909 | Optimizer | Silicone | One component | Room temperature curing | Transformer fixing |
S6909 | Micro inverter | Silicone | One component | Room temperature curing | Cover seal |
SS4-0328 | Micro inverter | Silicone | Two-component | Room temperature curing | Waterproof potting |
SW9339N | Micro inverter | Silicone | One component | Room temperature curing | Antenna sealing |
S1-9339 | Panel Sealing | Silicone | One component | Room temperature curing | Panel Sealing |
S7609 | Panel coating | Silicone | One component | Room temperature curing | Panel coating |
S1-9339 | Junction Box | Silicone | One component | Room temperature curing | Junction box bonding |
Power and Accessories
Silicone grease is an integral part of the puncture clamp, and high-performance greases enhance reliable lubrication protection. High performance grease with very low freeness and good lubricating effect.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
S592 | Piercing Connector | Silicone | One-component | Room temperature curing | Lubrication protection |
Thermal power generation
The anti-corrosion solution can greatly reduce the corrosion from the positive pressure acid on the inner wall of the chimney, greatly extending the service life and maintenance period of the chimney.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
SS032 | Power station chimney | Silicone | Two-component | Room temperature curing | Resistance to high temperature humidity acid |
Living Appliances
Silicone is the preferred material which can optimizing the kitchen appliances when during producing, like microwave oven, oven, electric stove, range hood, disinfection Cabinet, refrigerator, dishwasher, electric cooker, bathroom heater, water heater, ventilation, heating systems. After curing, Silicone is safe in ecology and physiology, suitable for food contact applications, and even used for molding like chocolate and Popsicle making.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
SR2019 | Electric iron | Silicone | One component | Room temperature curing | Sink sealing |
SR2019 | Electric iron | Silicone | One component | Room temperature curing | Floor bonding |
S0609 | Air conditioner/Bath heater/Vacuum cleaner | Silicone | One component | Room temperature curing | PCB coating |
E8166 | Television | Epoxy | One component | Heat curing | Low temperature epoxy for backlight modules |
PP0906 | Vacuum cleaner | Polyurethane | Two-component | Room temperature curing or Heat curing | Control board motor bonding |
EE2116 | Electric blanket/ Fitness machine | Epoxy | Two-component | Heat curing | Control panel potting |
Kitchen Appliance
In terms of simple isolation safety function, silicone, epoxy resin, polyurethane sealant and potting adhesive are all waterproof, confidential and easy to repair, making them suitable for air conditioners, TV, bath heater, vacuum cleaners, massage chairs, fitness machines, electric blankets and so on.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
S6629 | Microwave oven | Silicone | One component | Room temperature curing | Floor bonding |
S6019 | Microwave oven | Silicone | One component | Room temperature curing | Glass door bonding |
S6019 | Rice cooker | Silicone | One component | Room temperature curing | Heating base bonding |
S5629 | Rice cooker | Silicone | One component | Room temperature curing | Heating base bonding |
S9339N | Rice cooker | Silicone | One component | Room temperature curing | Heating base bonding |
S3019 | Oven | Silicone | One component | Room temperature curing | Door sealing |
S6019 | Disinfection cabinet | Silicone | One component | Room temperature curing | Door sealing |
S6019 | Disinfection cabinet | Silicone | One component | Room temperature curing | Hand bonding |
S3019 | Water heater | Silicone | One component | Room temperature curing | Heating pipe plug bonding |
S0249 | Water heater | Silicone | One component | Room temperature curing | Heating pipe plug bonding |
S2111 | Water heater | Silicone | One component | Room temperature curing | Combustion chamber cooling grease |
S8019 | Kitchen ventilator | Silicone | One component | Room temperature curing | Glass cover bonding |
SS0358 | Coffee pot | Silicone | Two-component | Room temperature curing | Glass and base bonding |
S9339N | Coffee pot | Silicone | One component | Room temperature curing | Glass and base bonding |
S6019 | Coffee pot | Silicone | One component | Room temperature curing | Heating coil bonding |
S8019 | Cooker | Silicone | One component | Room temperature curing | Glass cover bonding |
Consumer Electronics
In handheld devices,we provide comprehensive solutions such as: LCD and TP lamination, camera module assembly bonding, UBS waterproof sealing, speaker sealing, PCB coating, power device cooling. Excellent and reliable performance is the best choice for living electronic equipment.
PRODUCT | APPLICATION | CATEGORY | TYPE | CURING | APPLICATION |
SS8-8078 | LCD and TP lamination | Silicone | Two-component | Room temperature curing | Touch screen and LCD screen bonding |
SS2068 | LCD and TP lamination | Silicone | Two-component | Room temperature curing | Touch screen and LCD screen bonding |
S41-1B2019 | Type C connector | Silicone | One component | Room temperature curing | PIN pin bonding |
EERF5226 | Camera module | Epoxy | Two-component | Heat curing | Lens and base bonding |
EE2116 | Speaker | Epoxy | Two-component | Heat curing | Internal device potting |
S6139 | Heat Sink of Power device | Silicone | One component | Room temperature curing | Component heat bonding |
S2111 | Heat Sink of Power device | Silicone | One component | Room temperature curing | Component heat sinking |
S5211 | Heat Sink of Power device | Silicone | One component | Room temperature curing | Component heat sinking |
Sl129 | PCB Conformal coating | Silicone | One component | Room temperature curing | PCB coating |
S0609 | PCB Conformal coating | Silicone | One component | Room temperature curing | PCB coating |