One Component Silicone Potting Sealant

Chasil 2019 3019 6019 Deoxime type good adhesion rtv silicone sealant

1. Resistance to moisture, dirt and other atmospheric components

2. Reduce the mechanical stress and tension caused by mechanical, thermal shock and vibration

3. Excellent electrical insulation, anti-corona

4. Outdoor aging excellent, the service life of up to 20-30 years

5. To overcome the 280 ℃thermal aging test under the smoke, bubbling, sticky and powder phenomenon

Color: Transparent, Black, White, Red

Application:

1. Steam iron

2. oven

3. high temperature air filter

4. high temperature oven

5. high temperature pipe and other industrial products

6. high temperature requirements

Way of Use:

1. clean the surface: the sticky or coated surface will be clean, clean with detergent to remove rust, dust and oil and so on.
   

2. sizing: the plastic mouth cut to the required size, into the glue gun. Squeeze the glue into the clean surface, so that the distribution of uniform. When bonding, it will be fixed by the sticky surface.

3. curing: the painted parts will be placed in the air, room temperature 24 hours curing about 2mm thickness.

4. Note: Open as soon as possible once ran out, once not used up, re-use, squeeze the cured part, continue to use, does not affect the normal use.

5. The use of dispensing equipment, please contact BEGINOR market sector.

6. A large area after the need to meet the temperature of 300 degrees of application technology. After 3

7. days of solidification of silica gel, the initial temperature rise procedure should be carried out before the high temperature environment of 300 degrees: After the colloid is fully cured (8mm thickness is 24 days at 23 ℃ 55% humidity, the curing time should be prolonged when the temperature and humidity are low) 80 ° C → 120°C → 160°C → 200°C → 220°C → 240°C → 260°C → 280°C → 300°C. The

8. program temperature is kept for 60 min.

Packing and Stocking

310 ML/tube,25 pcs/box

The storage period at 25 ℃ is 12 months. Over the storage period please sampling test.

Chasil 1009 High transparency one component dealcohol type flow silicone sealant gel

1. Low viscosity, good flow

2. High transparency and high physical and mechanical properties

3. Excellent insulation performance

4. It is damp-proof, dust-proof, corona proof and shockproof

5. Good high and low temperature resistance, temperature tolerance range is 60 ~ 260 ℃

6. Excellent aging resistance, service life up to 20 ~ 30 years

7. After curing, the colloid does not turn yellow, does not leak oil, the comprehensive performance is excellent

Color: Transparent fluid

Packging: 310ml

Application:

1. LED lamps sealed

2. Plastic metal shell sealing

3. PCB board components

4. Wiring harness fixed

5. Electronic

Way of Use

Apply a bead of Chasil 1009 Adhesive/Sealant (see Handling Precautions) to one of the prepared surfaces, then quickly cover with the other substrate to be bonded.

On exposure to moisture, the freshly applied material will “skin-over” in about 3-5 minutes at room temperature and 50% relative humidity. Any tooling should be completed before this skin forms. The surface is easily tooled with a spatula. The adhesive/sealant will be tack-free in approximately 10 minutes.

Chasil 2009 one-component fast tack free time flowable silicones sealant

1. a one-component, fast skin-curing, non-corrosive silicone adhesive sealant that cures on exposure bymoisture to form an elastic silicone rubber.

2. In between -60-260 ℃ stable mechanical and electrical properties

3. Excellent outdoor aging, the service life of up to 20-30 years

Color: Clear, Transparent fluid

Packaging: 310ml

Application:

1. LED lamps sealed

2. Plastic metal shell sealing

3. PCB board components

4. Wiring harness fixed

5. Electronic

Way of Use

Apply a bead of Chasil 2009 Adhesive/Sealant (see Handling Precautions) to one of the prepared surfaces, then quickly cover with the other substrate to be bonded.

On exposure to moisture, the freshly applied material will “skin-over” in about 3-5 minutes at room temperature and 50% relative humidity. Any tooling should be completed before this skin forms. The surface is easily tooled with a spatula. The adhesive/sealant will be tack-free in approximately 10 minutes.

Chasil 1237 neutral dealcoholized organic one component silicone adhesive

1. One component, easy operation, short tack free time
   

2. Excellent chemical resistance

3. Moisture, dirt and other atmospheric composition proof

4. Relieving the mechanical stress and tension that cased by machinery, heat shock and vibrate

5. Good corona resistance and electrical insulation performance

6. Excellent outdoor aging-resistance for 20-30 years

7. Stable mechanical and electrical properties between -60-260°C

Color: Black, White

Packaging:   310ml, 5kg

Application:

For sealing LED lamps, plastic or metal shell sealing, PCB components and wiring harness fixing.

As waterproof coating for delicate electronic accessories and electrical communication equipment.

For potting and plugging of small module, optical display and circuit board which thickness is under 6mm.

Way of Use:

Cleaning: cleaning the surfaces that to be glued and coated, removing the rust, dust, greasy dirt and other foreign matter and substance.

Gluing: cutting nozzle to the required angle(piercing the sealing cap tip for these sealing rubber hose), extruding the liquid cement to the cleaned surface and making it well-distributed, then folding and fixing the glued surfaces. Please consult Sepna market department when come into the dispensing equipment.

Curing: thecuring process is start from surface to internal, the cured depth is about 2~4mm in room temperature, 55%RH. It should cost more time for curing to a thicker glue layer, lower temperature also will extend the curing time. It takes more than 3 days for a 6mm thick glue layer to fully cured.

Attention: tightening and sealing preserve the leftover sealant after the operation. Removing the cured cement at the sealing part that might happen during the preservation, it could be normally used again.

Chasil 3339 Semi-flowable one-component, non-corrosive RTV silicone sealant

1. a one-component, non-corrosive silicone adhesive sealant that cures on exposure bymoisture to form an elastic silicone rubber.
   

2. Semi-flowableand has excellent corrosion-free adhesion to metals, including copper, plastics, ceramics, glass, etc, without the use of primers.

3. Excellent high and low temperature resistance: from –60℃ to 250℃.

4. Excellent weather ability, water and chemical resistance

5. Excellent electrical insulation properties.

6. Simple and easy-to-use one-component system.

Packaging: 310ml

Application:

1. Electricity

2. Solar

3. Equipment

4. House-hold

5. LED lighting

6. Power supplies

7. Mould

8. Semi-conductor

Way of Use

1. Clean the surface thoroughly, keep dry and loose debris.

2. Clean with a solvent.

3. Cut the tip off cartridge and attach nozzle to cartridge. Full the joint completely.

4. Sealant skins in 20 minutes, is touched dry in 15 minutes and cures in 1-2 days depending on application.

5. Full bond strength is achieved in 7 days.

6. Apply a bead of Chasil 3339 Adhesive/Sealant (see Handling Precautions) to one of the prepared surfaces, then quickly cover with the other substrate to be bonded.
   

7. On exposure to moisture, the freshly applied material will “skin-over” in about 15 minutes at room temperature and 50% relative humidity. Any tooling should be completed before this skin forms. The surface is easily tooled with a spatula. The adhesive/sealant will be tack-free in approximately 20 minutes.

8. Cure time

9. After skin formation cure continues inward from the surface. In 24 hours (at room temperature and 50% relative humidity) Chasil 3339 Adhesive/Sealant will cure to a depthof about 3mm. Very deep sections, especially when access to atmospheric moisture is restricted, will take longer to cure completely. Cure time is extended at lower humidity levels. Before handling and packaging bonded components, users are advised to wait a sufficiently long time to ensure that the integrity of the adhesive seal is not affected. This will depend on many factors and should be determined by the user for each specific application.

Chasil 3009 room-temperature flowable one-part clear silicone sealant

1. Room-temperature curing;

2. Resist humidity and other harsh environments;

3. Excellent mechanical properties

4. good dielectric properties;

5. self-priming adhesion; low stress

Color: Clear

Packaging: 310ml

Application: LED lamps sealed, plastic metal shell sealing; PCB board components, wiring harness fixed. Electronic accessories, electrical and communications equipment coating

Way of Use

Apply Chasil 3009 Adhesive/Sealant to one of the prepared surfaces, then quickly cover with the other substrate to be bonded.

On exposure to moisture, the freshly applied material will “skin-over” in about 20 minutes at room temperature and 50% relative humidity. Any tooling should be completed before this skin forms. The surface is easily tooled with a spatula. The adhesive/sealant will be tack-free in approximately 20 minutes.

Chasil 8339 good dielectric,low stress RTV silicones sealant

1. Flowable, one-part, silicones sealant.
   

   
   

2. Physical Form

   cure to flexible elastomers
   

   Special Properties

   
   

3. Room-temperature curing;

   Resist humidity and other harsh environments;

   good dielectric properties;   self-priming adhesion;

   low stress;

1. A one-component, fast skin-curing, non-corrosive silicone adhesive sealant that cures on exposure by moisture to form an elastic silicone rubber.

2. Excellent corrosion-free adhesion to metals, including copper, plastics, ceramics, glass, etc, without the use of primers.

3. Excellent high and low temperature resistance: from –60℃to 260℃.

4. Excellent chemical resistance, resistant to moisture, dirt and other atmospheric components.

5. Reduce mechanical, thermal shock and vibration caused by mechanical stress and tension.

6. Simple and easy-to-use one-component system. Non-stick hand, a shorter time     In between -60-260 ℃ stable mechanical and electrical properties

7. Excellent outdoor aging, the service life of up to 20-30 years

Color: Clear, White

Application:

LED lamps sealed, plastic metal shell sealing;

PCB board components, wiring harness fixed.

Electronic accessories

Communications equipment coating

Way of Use

Apply a bead of Chasil 8339Adhesive/Sealant (see Handling Precautions) to one of the prepared surfaces, then quickly cover with the other substrate to be bonded.

On exposure to moisture, the freshly applied material will “skin-over” in about 3-5 minutes at room temperature and 50% relative humidity. Any tooling should be completed before this skin forms. The surface is easily tooled with a spatula. The adhesive/sealant will be tack-free in approximately 10 minutes.

Cure time

After skin formation时 cure continues inward from the surface. In 24 hours (at room temperature and 55% relative humidity) Besil 9338 Adhesive/Sealant will cure to a depthof about 3~4mm. Very deep sections, especially when access to atmospheric moisture is restricted, will take longer to cure completely. Cure time is extended at lower humidity levels. Before handling and packaging bonded components, users are advised to wait a sufficiently long time to ensure that the integrity of the adhesive seal is not affected. This will depend on many factors and should be determined by the user for each specific application.

USABLE LIFE AND STORAGE

When stored at or below 300C (860F) inthe original unopened containers, this product has a usable life of 12 months from the date of production.

Packaging

310ML/tube, 25tubes/box; 100ML/tube,100tubes/box;